Miele WCI 320 Operating Instructions Manual Download

Page: 23 / 92

2. Select a programme

Switching on the washing
machine



Turn the programme selector to a
programme.

Programme selection

1. Select standard programmes with
the programme selector dial



Turn the programme selector to the
required programme.

The selected programme will be shown
in the display. The standard display will
then appear.

2. Select additional programmes by
setting the programme selector to
the “Further programmes/



”

position and using the display:



Turn the programme selector to the

Further programmes/



position.

The following appears in the display:

Express 20











Touch the



sensors until the

programme you want appears in the
display.



Confirm the programme with the

sensor.

Preset programme parameters will be
displayed, depending on the
programme selected.

Summary of Contents for WCI 320





























































































Search results

Summary of Contents for WCI 320

Reviews:

Related manuals for WCI 320

Brands by name

Popular brands

Miele WCI 320, Operating Instructions Manual

Search results

Summary of Contents for WCI 320

Reviews:

Related manuals for WCI 320

Brands by name

Popular brands