background image

Warning and Safety instructions

10

 

If the electrical connection cable is faulty it must only be replaced

by a Miele authorised service technician to protect the user from
danger.

 

The machine must be isolated from the electricity supply when

cleaning and maintaining the machine and in the event of a fault.

 

The machine must only be connected to the on-site water supply

using a new hose kit. Old hose kits must not be re-used. Check the
condition of the hoses regularly so that you can replace them in
good time and avoid the risk of any water damage.

 

The water flow pressure must be at least 100 kPa and should not

exceed 1000 kPa.

 

In areas which may be subject to infestation by cockroaches or

other vermin, pay particular attention to keeping the machine and its
surroundings in a clean condition at all times. Any damage which
may be caused by cockroaches or other vermin will not be covered
by the warranty.

 

The machine must not be used in a non-stationary location (e.g.

on a ship).

 

Do not make any alterations to the machine, unless authorised to

do so by Miele.

Summary of Contents for WCI 320





























































































Reviews: