Miele WCI 320 Operating Instructions Manual Download

Page: 55 / 92

Cleaning and care

Cleaning the siphon and the





compartment channel

Liquid starch results in clogging. If
clogged, the siphon in the





compartment will not work and the
compartment can overflow.
Clean the siphon particularly
thoroughly after using liquid starch a
few times.

Remove the siphon from



compartment and clean under warm
running water. Clean the siphon tube
in the same way.

Replace the siphon.



Clean the fabric conditioner channel
using a brush and warm water.

Cleaning the detergent dispenser
drawer compartment



Use a bottle brush to remove
detergent residues and limescale
from the jets inside the detergent
dispenser drawer compartment.



Replace the detergent dispenser
drawer.

Tip:

Leave the detergent dispenser

drawer slightly open to allow it to dry.

Summary of Contents for WCI 320





























































































Search results

Summary of Contents for WCI 320

Reviews:

Related manuals for WCI 320

Brands by name

Popular brands

Miele WCI 320, Operating Instructions Manual

Search results

Summary of Contents for WCI 320

Reviews:

Related manuals for WCI 320

Brands by name

Popular brands