Miele TKG 450 WP Operating Instructions Manual Download Page 71

Page: 71 / 80

Installation and connection

Electrical connection

This tumble dryer is supplied with a

mains cable with moulded plug.
The accessibility of the plug must be

always ensured in order to separate the

tumble dryer from the mains.
Connection of this appliance should

comply with national and local safety

regulations.
Do not connect the appliance via an

extension lead. Extension leads do not

guarantee the required safety of the

appliance (e.g. danger of overheating).
The appliance should be connected up

only by a qualified electrician in

accordance with national and local

safety regulations. For extra safety, it is

advisable to install a residual current

device (RCD) with a trip current of 30

mA.
The voltage, rated load and plug rating

are given on the data plate. Please

ensure that these match the household

mains supply.

Important

The wires in the mains lead are

coloured in accordance with the

following code:

Green/yellow = earth

Blue = neutral

Brown = live

As the colours of the wires in the mains

lead of this appliance may not

correspond with the coloured markings

identifying the terminals in your plug,

proceed as follows: The wire which is

coloured green and yellow must be

connected to the terminal in the plug

which is marked with the letter E or by

the earth symbol or coloured green or

green and yellow. The wire which is

coloured blue must be connected to the

terminal which is marked with the letter

N or coloured black. The wire which is

coloured brown must be connected to

the terminal which is marked with the

letter A or coloured red.

WARNING

THIS APPLIANCE MUST BE

EARTHED

Summary of Contents for TKG 450 WP

















































































Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands

Miele TKG 450 WP, Operating Instructions Manual

Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands