Miele TKG 450 WP Operating Instructions Manual Download Page 49

Page: 49 / 80

Fragrance flacon

The fragrance will also be noticeable in

the room air during the process.

Fragrance is not released when using

the

Cool air

programme.

After drying

To avoid the fragrance escaping

needlessly:



Turn the outer ring anti-clockwise

until marker

is in position

– You will feel a slight resistance.

If you want to dry laundry without

adding fragrance occasionally: remove

the fragrance flacon and store it in its

original packaging until you want to

use it again. See the following section.

Replacing the fragrance flacon

When the fragrance is no longer

sufficiently intense:



Turn the outer ring anti-clockwise

until markers

and

line up.



Replace the fragrance flacon with a

new one.

Fragrance flacons are available to

order from Miele or online at

www.miele-shop.com (depending on

country).

Summary of Contents for TKG 450 WP

















































































Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands

Miele TKG 450 WP, Operating Instructions Manual

Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands