Miele TKG 450 WP Operating Instructions Manual Download Page 36

Page: 36 / 80

Programme chart

Proofing

Max. load 2.5 kg*

Normal

Items

Drying microfibre fabric, skiwear, outerwear, fine, closeweave cotton

garments (poplin) or tablecloths which are suitable for drying in a

tumble dryer and have been treated to provide a water and dirt-

resistant finish.

Notes

– This programme includes a proofing fixing phase.
– Only use proofing agents which are stated by the manufacturer as

being "suitable for use on membrane textiles" as these contain

fluorochemical compounds.

– Do not dry items which have been treated with proofing agents

containing paraffin. Fire hazard!

Sportswear

Max. load 3.0 kg*

, Normal, Slightly dry, Hand iron



, Hand iron



Items

Sportswear which is suitable for drying in a tumble dryer.

* Weight of dry laundry

Summary of Contents for TKG 450 WP

















































































Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands

Miele TKG 450 WP, Operating Instructions Manual

Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands