Miele TKG 450 WP Operating Instructions Manual Download Page 9

Page: 9 / 80

Warning and Safety instructions



In the event of a fault or for cleaning purposes, the tumble dryer is

only completely isolated from the electricity supply when:

– it is switched off at the wall socket and the plug is withdrawn, or
– it is switched off at the mains circuit breaker.



This tumble dryer must not be installed and operated in mobile

installations (e.g. on a ship).



Do not make any alterations to the tumble dryer, unless

authorised to do so by Miele.



Heat pump technology and refrigerant:

The heat pump in this tumble dryer uses a refrigerant which is

condensed by the compressor and led in a closed circuit through

the heat exchanger unit where heat exchange with the circulating

drying air takes place.

– The humming noises caused by the heat pump are normal and do

not impair the efficient functioning of the dryer.

– The refrigerant is not flammable or explosive.
– In general it is not necessary to leave the dryer standing for any

length of time before it is connected to the mains provided it has

been transported and installed correctly.

Summary of Contents for TKG 450 WP

















































































Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands

Miele TKG 450 WP, Operating Instructions Manual

Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands