Miele TKG 450 WP Operating Instructions Manual Download Page 66

Page: 66 / 80

Installation and connection

Additional installation

requirements



The dryer should not be installed

next to a refrigeration appliance. The

warm air expelled from the rear of

the dryer would increase the

temperature around the refrigeration

appliance's heat exchanger causing

the compressor to run continuously.

If it is not possible to install the dryer

anywhere else, then the refrigeration

appliance must be sealed off from

the dryer.

It is very important to avoid a build-

up of heat. The warm air which is

expelled from the dryer must be able

to dissipate. Warm air which cannot

dissipate could cause a fault.

A build-up of heat can be avoided by:

– Adjusting the screw feet so that there

is a gap of at least 20 mm between

the floor and the bottom of the dryer.

– Creating a gap for the dryer in the

kitchen furniture plinth facing.

– Creating ventilation gaps in the

kitchen unit.

Suitable for pushing under a worktop

This tumble dryer is suitable for

pushing under a worktop.

– The appliance lid must not be

removed.

– The electrical socket must be located

in an accessible position near the

appliance.

– Drying durations may increase

slightly.

Optional accessories

– Washer-dryer stack

The tumble dryer can also be combined

with a Miele washing machine in a

washer-dryer stack. The appropriate

Miele washer-dryer stacking kit is

required.

Summary of Contents for TKG 450 WP

















































































Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands

Miele TKG 450 WP, Operating Instructions Manual

Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands