Miele TKG 450 WP Operating Instructions Manual Download Page 60

Page: 60 / 80

Problem solving guide

Steam smoothing spray jet



Limescale deposits will impair

the spray jet.
In this case, the spray jet must be

removed and replaced with a new

one (see "Optional accessories").

The spray jet can only be replaced

using the special tool supplied with the

new spray jet.



Do not use any other tool as this

would damage the spray jet or the

dryer.



Steam smoothing must never be

used without the spray jet fitted and

screwed in correctly.



Open the door of the tumble dryer.

The spray jet is located in the top left of

the door opening.



Attach the tool to the spray jet.



Turn the tool anti-clockwise to

unscrew the spray jet.



Insert the new spray jet in the tool.



Turn the tool clockwise to screw the

spray jet securely in position.

Summary of Contents for TKG 450 WP

















































































Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands

Miele TKG 450 WP, Operating Instructions Manual

Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands