Miele TKG 450 WP Operating Instructions Manual Download Page 56

Page: 56 / 80

Problem solving guide

Problem

Possible cause and remedy

There are humming

noises

This is not a fault.
The compressor (heat pump) is operating or you have

selected the

Steam smoothing

programme.



No action is required. These noises are quite

normal and can be heard when the compressor or

the condensed water pump is operating.

A programme cannot

be started

There is no obvious cause.



Connect the tumble dryer to the mains electricity

supply.



Turn on the tumble dryer.



Close the door.



Check whether the mains fuse has tripped.

Has there been a power cut? When power is

restored, any previously running programme will

restart automatically.

The display is dark and

the

Start/Stop

button is

flashing slowly

The dryer is in standby. This is a normal function and

does not indicate a fault.
The drum will turn at intervals in the anti-crease

phase.



See "Settings menu - Dark display".

The dryer is switched

off at the end of the

programme

The dryer switched off automatically. This is quite

normal and does not indicate a fault.



See "Settings menu - Appliance switch-off".

The interior drum

lighting does not come

The drum lighting will switch off automatically ...

... when the door is closed.

... after a few minutes when the door is open (to save

energy).

If the dryer is switched on, the drum lighting will

come on when the door is opened.

Summary of Contents for TKG 450 WP

















































































Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands

Miele TKG 450 WP, Operating Instructions Manual

Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands