Miele TKG 450 WP Operating Instructions Manual Download Page 52

Page: 52 / 80

Problem solving guide

Problem

Possible cause and remedy



Clean out airways

lights

up at the end of a

programme

There is a build-up of fluff in the airways.



Clean the fluff filters.



Clean the plinth filter.

See "Cleaning and care".
To switch off the message:



Select



Clean out airways See



lights up after a

programme is cancelled

An excessive amount of fluff has built up.



Clean the fluff filters.



Clean the plinth filter.

Clean the airways:



Clean the area underneath the plinth filter.



Clean the heat exchanger.

To switch off the message:



Switch the dryer off and back on again.



Empty container See



lights up after a

programme is cancelled

The condensed water container is full or there is a

kink in the drain hose.



Empty out the condensed water container.



Check the drain hose.

To switch off the message:



Open and close the door while the dryer is

switched on or switch the dryer off and back on

again.



Fill condensate container

This is to remind you that water is taken from the

condensed water container when the

Steam

smoothing

programme is being used.

The condensed water container must be filled with

water to at least the

–min–

marker.



Confirm with



Open & close door

This it to remind you to load the laundry when the

Steam smoothing

programme is selected.



Load the laundry in the drum.

Summary of Contents for TKG 450 WP

















































































Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands

Miele TKG 450 WP, Operating Instructions Manual

Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands