Miele TKG 450 WP Operating Instructions Manual Download Page 74

Page: 74 / 80

Settings menu

Calling up settings

The Settings menu is used to alter the

dryer's electronics to suit different

requirements. Settings can be altered

at any time.

Opening the Settings menu



Switch the tumble dryer on.

The programme selector must not be at

the

Further programmes

position.



Touch the



and



sensors at the

same time.

The following will light up in the display:

Language 



You are now in the Settings menu.

Selecting settings



Touch the





sensor until the

setting you want appears in the

display.

– The



sensor scrolls down the list.

– The



sensor scrolls up the list.



Confirm by touching the

sensor.

Changing a setting



Touching the





sensor will call

up the different options for the

setting.

For example, you can

– select a value. If the option is marked

with a



it is active.

– change a bar chart.
– change numbers.



Confirm by touching the

sensor.

Closing the Settings menu



Touch the





sensor repeatedly

until

Back



appears in the display.



Confirm by touching the

sensor.

Language



The display can be set to appear in

one of several different languages.

The flag



after the word Language

(Sprache in German) acts as a guide in

case a language which is not

understood has been set.

Summary of Contents for TKG 450 WP

















































































Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands

Miele TKG 450 WP, Operating Instructions Manual

Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands