Miele TKG 450 WP Operating Instructions Manual Download Page 38

Page: 38 / 80

Changing the programme sequence

You cannot change to another

programme once a programme has

started (this prevents unintentional

alterations).
If you move the programme selector,

Cannot be changed

will light up in the

display until you move the programme

selector back to the original

programme.
You will need to cancel the current

programme before you can select a

new one.

Cancelling a programme while

it is running and selecting a

new programme



Press the

Start/Stop

button.

Cancel programme

will light up in the

display.



Confirm by touching the

sensor.

–

Cooling down

will light up in the

display, depending on the drying

duration and the drying temperature

reached.

– Wait until

Finish

lights up in the

display or press the

Start/Stop

button again until

Finish

lights up.



Press the



button to switch the

dryer off.



Press the



button to switch the

dryer on.



Select and start a new programme

straight away.

Adding or removing laundry

after a programme has started



Press the

Start/Stop

button.

Cancel programme

will light up in the

display.



Confirm by touching the

sensor.

–

Cooling down

will light up in the

display, depending on the drying

duration and the drying temperature

reached.

– Wait until

Finish

lights up in the

display or press the

Start/Stop

button again until

Finish

lights up.



Danger of burning!

Do not touch the back of the drum

when adding or removing items. The

drum and the items can be very hot.



Add or remove items.



Close the door.

To continue with the programme:
(change the drying level first of all, if

necessary)



Press the

Start/Stop

button.

Programme duration

Altering the programme sequence can

cause the programme duration shown

in the display to be adjusted.

Summary of Contents for TKG 450 WP

















































































Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands

Miele TKG 450 WP, Operating Instructions Manual

Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands