Miele TKG 450 WP Operating Instructions Manual Download Page 25

Page: 25 / 80

3. Selecting a programme and starting it

Selecting a programme



Turn the programme selector.

Different programmes and setting

options will light up in the display,

depending on the position of the

programme selector.

When a programme is selected, the

maximum load (weight of dry laundry)

possible for the programme will

appear in the display for a few

seconds.

You can confirm with

or wait until

the preset drying level or programme

duration lights up.

If you think you have loaded too

much laundry, remove a few items.

Further programmes

The further programmes can be

selected via the display.

Automatic plus





Touch the





sensor to scroll

through the list until the programme

you want appears in the display.



Confirm by touching the

sensor.

Summary of Contents for TKG 450 WP

















































































Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands

Miele TKG 450 WP, Operating Instructions Manual

Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands