Miele TKG 450 WP Operating Instructions Manual Download Page 24

Page: 24 / 80

2. Loading the tumble dryer



It is essential to read "1. Notes

on correct laundry care" first of

all.



Switch the tumble dryer on by

pressing the



button.

The interior drum lighting will come on.

The interior drum lighting will

automatically go out after a few

minutes and/or after the start of a

programme to save energy.

Opening the door



Reach under the door grip and pull

the door open.



Unfold the laundry and load loosely

into the drum.

Do not overload the drum.
Overloading can cause unnecessary

wear and tear to the laundry, give a

disappointing drying result and

cause more creasing.

When closing the door, make sure

that laundry does not get trapped in

the door opening.
This could damage the laundry.

If you are not using a fragrance

flacon: the tab must be pushed

down completely (see arrow).

Closing the door



Shut the door with a gentle swing.

Summary of Contents for TKG 450 WP

















































































Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands

Miele TKG 450 WP, Operating Instructions Manual

Search results

Summary of Contents for TKG 450 WP

Reviews:

Related manuals for TKG 450 WP

Brands by name

Popular brands