Miele Standard Operating Instructions Manual Download Page 80 | Manualshive

Page: 80 / 96

background image

This dishwasher is supplied with a
mains cable and moulded plug ready
for connection to an AC single phase
supply, (230 V 50 Hz for NZ and
Australia) via a fused plug and suitable
switched socket.

,

The electrical socket must be

easily accessible after the
dishwasher has been installed.
Do not connect the washing
machine to the mains electricity
supply by an extension lead.
Extension leads do not guarantee
the required safety of the appliance
(e.g. danger of overheating).

If the connection cable is damaged, it
must be replaced by a Miele approved
service technician only in order to
protect the user from danger.

Connection should be made via a
suitable switched socket which is easily
accessible. For extra safety, it is
advisable to install a suitable residual
current device (RCD).
The appliance must not be connected
to an isolated inverter which is
connected to a self-sufficient power
supply, e.g. solar power supply.
Voltage peaks when the appliance is
switched on can cause a safety
switch-off and the electronics may also
be damaged. The appliance must not
be operated in conjunction with
energy-saving plugs either as the
energy intake of the appliance is
reduced and it will overheat.

,

Before connecting the

dishwasher, check that the
connection data on the data plate
(voltage and rated load) matches
the mains electricity supply. If in any
doubt, consult a qualified
electrician.

Technical data can be found on the
data plate on the right-hand side of the
door.

Electrical connection

80

«
...
78
79
80
81
82
...
»

Summary of Contents for Standard

































































































Reviews:

No comments

Related manuals for Standard

Brand: Favor.it Pages: 9

Brand: Asko Pages: 16

Brand: Fisher & Paykel Pages: 20

Brand: ZANKER Pages: 40

Brand: Ariston Pages: 72

Brand: Belling Pages: 24

Brand: Blanco Pages: 16

Brand: Technika Pages: 13

Brand: Smeg Pages: 35

Brand: VOX electronics Pages: 188

Brand: Ariston Pages: 60

AdorinaDry V400

Brand: V-ZUG Pages: 100

Brand: Gaggenau Pages: 28

VVW7040BS Series

Brand: inventum Pages: 112

Brand: Bosch Pages: 68

Brand: GE Pages: 20

Spacemaker DSKS333ECWW

Brand: GE Pages: 4

Brand: GE Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands