background image

Adjusting the upper basket

In order to gain more space for taller
pieces of crockery in the bottom or
upper basket, the upper basket can be
adjusted on three levels with 2 cm
between each level.

The upper basket can also be set at an
angle with one side high and the other
side low. This can be useful to help
prevent water being left in deep dishes
etc. Ensure, however, that the basket
can be inserted smoothly into the
cabinet. It is better to adjust the basket
before loading it.

^

Pull out the upper basket.

To raise the upper basket:

^

Pull the basket up until it clicks into
place.

To lower the upper basket:

^

Pull upwards on the levers at either
side of the upper basket.

^

Adjust the basket to the desired
height and then push the levers
securely back down into position.

Depending on the setting of the upper
basket, the following plate dimensions
can be accommodated.

Dishwasher with cutlery tray

(see data plate for model number)

Upper

basket

level

Plate

C

in cm

Upper basket

Lower

basket

Normal

XXL

Top

15

19

31

Middle

17

21

29

Bottom

19

23

27

Dishwasher with cutlery basket

(see data plate for model number)

Upper

basket

level

Plate

C

in cm

Upper basket

Lower

basket

Normal

XXL

Top

20

24

31

Middle

22

26

29

Bottom

24

28

27

Loading the dishwasher

35

Summary of Contents for Standard

































































































Reviews: