Miele Standard Operating Instructions Manual Download Page 14

Page: 14 / 96

Correct use

Do not use solvents in the dishwasher. Danger of explosion!

Avoid inhalation of powder detergents. Dishwasher detergents

contain irritant or corrosive ingredients which can cause burning in
the nose, mouth and throat if swallowed, or inhibit breathing. Consult
a doctor immediately if detergent has been swallowed or inhaled.

Avoid leaving the door open unnecessarily as you could trip over

it.

Dishes can be very hot at the end of a programme.

Allow the dishes to cool until they are comfortable enough to handle
before unloading them.

Do not sit or lean on the opened door. This could cause the

dishwasher to tip and be damaged, and you could get injured.

Only use detergent and rinse aid formulated for domestic

dishwashers. Do not use washing-up liquid.

Do not use commercial or industrial detergents as these may

cause damage, and there is a risk of severe chemical reaction.

Warning and Safety instructions

Summary of Contents for Standard

































































































Search results

Summary of Contents for Standard

Reviews:

Related manuals for Standard

Brands by name

Popular brands

Miele Standard, Operating Instructions Manual

Search results

Summary of Contents for Standard

Reviews:

Related manuals for Standard

Brands by name

Popular brands