Miele Standard Operating Instructions Manual Download Page 55 | Manualshive

Page: 55 / 96

background image

Checking the filters in the
wash cabinet

The filter combination in the base of the
wash cabinet retains coarse soil from
the suds solution, preventing it
accessing the circulation system and
re-entering the cabinet through the
spray arms.

,

This dishwasher must not be

used without all the filters in place.

Collection of coarse soil may cause the
filters to clog. The level of soiling and
time it takes before the filters need
cleaning will vary depending on use.

The message

Check filters

will appear

in the display after every 50 programme
cycles (factory default setting).

You can set the interval for this
message to appear to between 30
and 60 programme cycles (see
"Settings

!

menu - Check filters").

^

Check the filter combination.

^

Clean it, if necessary.

^

Then confirm the message with

OK

.

The display will change to show the
programme selection menu.

Cleaning the filters

^

Switch the dishwasher off.

^

Turn the handle anti-clockwise to
release the filter combination

a

.

^

Take the filter combination out

b

,

remove any coarse particles and
rinse the filter well under running
water. Use a nylon brush if
necessary.

,

Ensure that course soil doesn't

get into the circulation system and
cause a blockage.

Cleaning and care

55

«
...
53
54
55
56
57
...
»

Summary of Contents for Standard

































































































Reviews:

No comments

Related manuals for Standard

Brand: Favor.it Pages: 9

Brand: Panasonic Pages: 44

Brand: Samsung Pages: 2

Brand: Samsung Pages: 52

Brand: Samsung Pages: 19

Brand: Samsung Pages: 44

Brand: Samsung Pages: 44

Brand: Samsung Pages: 44

WA55CG7500 Series

Brand: Samsung Pages: 76

WA70H4210S Series

Brand: Samsung Pages: 48

WD106U4SA Series

Brand: Samsung Pages: 44

Brand: Hanseatic Pages: 72

ODW 60032 FS A2

Brand: OK. Pages: 27

Brand: Gaggenau Pages: 24

Brand: Samsung Pages: 40

Brand: Samsung Pages: 48

Brand: Samsung Pages: 13

Brand: Samsung Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands