Miele Standard Operating Instructions Manual Download Page 65

Page: 65 / 96

Unsatisfactory washing result

Problem

Possible cause

Remedy

The dishes are not
clean.

The dishes were not loaded
correctly.

See notes in "Loading the
dishwasher".

The programme was not
powerful enough.

Select a more intensive
programme. See
Programme chart.

There is some stubborn
soiling although most of the
crockery is only lightly soiled
(e.g. with tea stains).

Use the "Adjust Sensor
wash" function (see
"Additional functions").

Not enough detergent was
used.

Use more detergent, or
change your detergent.

Items are blocking the path
of the spray arms.

Rearrange the items so that
the spray arms can rotate
freely.

The filter combination in the
base of the wash cabinet is
not clean or is not correctly
fitted.
This may cause the spray
arm jets to get blocked.

Clean and/or fit the filter
combination correctly. Clean
the spray arm jets. See
"Cleaning and care".

The non-return valve is
blocked in the open position.
Dirty water has flowed back
into the wash cabinet.

Clean the drain pump and
the non-return valve. See
"Maintenance - Cleaning the
drain pump and non-return
valve".

Smearing appears
on glassware and
cutlery, there is a
bluish sheen on
the surface of
glassware; film
can be wiped off.

The rinse aid dosage is set
too high.

Reduce the dosage. See
"Settings menu - Rinse aid".

Problem solving guide

Summary of Contents for Standard

































































































Search results

Summary of Contents for Standard

Reviews:

Related manuals for Standard

Brands by name

Popular brands

Miele Standard, Operating Instructions Manual

Search results

Summary of Contents for Standard

Reviews:

Related manuals for Standard

Brands by name

Popular brands