Miele G 7314 Operating Instructions Manual Download Page 90

Page: 90 / 124

Problem solving guide

Fault with the AutoDos (automatic dispensing)

Problem

Possible cause and remedy

The following message
appears in the display:

Insert PowerDisk or
deactivate AutoDos with OK

The



AutoDos

function is active but no PowerDisk

has been inserted.



Insert a PowerDisk (see “Detergents - Automatic
dispensing/AutoDos”).



If you do not wish to use automatic dispensing,
deactivate the function using

or the



AutoDos

sensor.

The alarm tone is
sounding.
The programme does
not start or a
programme that has
already started stops.
The following message
appears in the display:

AutoDos lid open

The AutoDos lid has not been closed properly.



Close the AutoDos lid and lock it fully (see
“Detergents - Automatic dispensing/AutoDos”).



If the lid cannot be fully closed, check whether the
PowerDisk holder is lying flat (see “Detergents -
Inserting a PowerDisk”).



If the same fault message appears again, call
Miele.

The following message
appears in the display:

PowerDisk empty.
Deactivate AutoDos with
OK.

The



AutoDos

function is active and the PowerDisk

is empty.



Replace the PowerDisk (see “Detergents -
Automatic dispensing/AutoDos”).
If you do not wish to use automatic dispensing,
deactivate the function using

or the



AutoDos

sensor.

The message

PowerDisk empty.
Deactivate AutoDos with
OK.

appears in the

display even though you
have inserted a new
PowerDisk.

The dishwasher was switched off when the
PowerDisk was replaced and it has therefore not
recognised the new PowerDisk.



Switch the dishwasher on before replacing the
PowerDisk (see “Detergents - Automatic
dispensing/AutoDos” and “Inserting a
PowerDisk”).

Summary of Contents for G 7314





























































































































Search results

Summary of Contents for G 7314

Reviews:

Related manuals for G 7314

Brands by name

Popular brands

Miele G 7314, Operating Instructions Manual

Search results

Summary of Contents for G 7314

Reviews:

Related manuals for G 7314

Brands by name

Popular brands