Miele G 6910 Operating Instructions Manual Download Page 8

Page: 8 / 96

IMPORTANT SAFETY INSTRUCTIONS

Technical safety



Installation, repair, and maintenance work should only be per‐

formed by a Miele-authorized service technician. Work by unquali‐

fied persons could be dangerous and may void the warranty.



Before installation, check the dishwasher for visible signs of dam‐

age. Under no circumstances should you use a damaged dishwash‐

er. A damaged dishwasher could be dangerous.



The electrical safety of this appliance can only be guaranteed

when continuity is complete between it and an effective grounding

system. It is most important that this basic safety requirement is

present and regularly tested and, where there is any doubt, the elec‐

trical system in the house should be checked by a qualified electri‐

cian.

Miele cannot be held liable for the consequences of an inadequate

grounding system (e.g. electric shock).



Reliable and safe operation of this dishwasher can only be assur‐

ed if it has been connected to the electrical supply.



The dishwasher must only be plugged into the electricity supply

via a suitable switched socket using a 3-pin plug with a grounding

contact (it must not be hard-wired). The electrical socket must be

easily accessible after the dishwasher is installed so that it can be

disconnected from the electricity supply at any time.



There must be no electrical sockets behind the dishwasher. There

is a danger of overheating and fire risk if the dishwasher is pushed

up against a plug.



The dishwasher must not be installed under a cooktop. The high

radiant temperatures which are sometimes generated by a cooktop

could damage the dishwasher. For the same reason, it should not be

installed next to open fires or other appliances which give off heat,

such as heaters, etc.

Summary of Contents for G 6910

































































































Search results

Summary of Contents for G 6910

Reviews:

Related manuals for G 6910

Brands by name

Popular brands

Miele G 6910, Operating Instructions Manual

Search results

Summary of Contents for G 6910

Reviews:

Related manuals for G 6910

Brands by name

Popular brands