Miele G 6910 Operating Instructions Manual Download Page 45

Page: 45 / 96

Operation

Starting a program

The dishwasher can be started only if

the door is closed.



Press the

Start

sensor button.

The program starts, and the prompt

Dishes can be added

appears in the dis‐

play.

As long as this prompt is showing,

dishware can be added without com‐

promising the wash results.



Water in the dishwasher may be

hot. Danger of scalding from water in

the cabinet.
Make sure you open the door very

carefully.

A program should only be canceled

in the first few minutes, if at all. Oth‐

erwise important program stages

could be omitted.

Time display

The estimated duration of the program

selected appears in hours and minutes

in the display before the program be‐

gins. During the program, the time left

until the end of the program is dis‐

played.
Each program stage is indicated by a

symbol:



Pre-wash / Soak



Main wash



Interim rinse



Final rinse



Drying



Finish

The program duration displayed may

vary with the same program. It is influ‐

enced by, among other things, the wa‐

ter temperature at each intake, the re‐

activation process, the type of deter‐

gent, the amount of dishware, and the

amount of soiling.
When a program is selected for the first

time, the display shows an average

time for a cold water intake.
The times shown in the program over‐

view refer to standard test loads and

temperatures.
Each time a program is run, the elec‐

tronic module calculates the program

duration required according to the tem‐

perature of the water taken into the

dishwasher and the amount of dish‐

ware.

Summary of Contents for G 6910

































































































Search results

Summary of Contents for G 6910

Reviews:

Related manuals for G 6910

Brands by name

Popular brands

Miele G 6910, Operating Instructions Manual

Search results

Summary of Contents for G 6910

Reviews:

Related manuals for G 6910

Brands by name

Popular brands