MERRICK MC3 35.00.EX Operation And Maintenance Manual Download Page 4

Page: 4 / 69

List of Physical Outputs ......................42

EMT Settings ...........................................43

Divisor .................................................43

Pulse Width .........................................43

Comm Settings ........................................43

Comm 1 Numeric ................................44

Comm 2 Numeric ................................44

Limit Switches..........................................45

Weight Limits.......................................45

Panel Meter Limits ..............................45

Calibrating Your Controller...............................46

Calibration Menu..........................................46

Zeroing Procedure...................................47

Material Calibration..................................48

Weight Procedure....................................49

Electronic Calibration ..............................50

E-Cal Factor Procedure...........................52

Analog Input Procedure...........................52

Diagnosing Problems .......................................54

The Crash Screen .......................................54

Start-Up Crash.........................................54

Parameter Corruption .........................54

Controller Firmware Upgrade..............54

Fatal Error Crash .....................................55

Forcing a Parameter Reset ................ 56

Diagnostic Menus........................................ 56

HPAD Diagnostics................................... 56

Communication Diagnostic ..................... 57

Clean Off Screen..................................... 59

Calibrate Diag ......................................... 59

Analog Diagnostics ................................. 59

Digital Diagnostics................................... 60

Mapping view ...................................... 60

List View.............................................. 61

Faults and Warnings Diagnostics ........... 61

DF1 Diagnostics ...................................... 61

Misc Data Diagnostics............................. 62

Modbus Diagnostics ........................... 63

Diagnostic Settings...................................... 63

HPAD Settings ........................................ 63

CAL ..................................................... 63

ZERO .................................................. 63

GAIN ................................................... 64

Set Status ........................................... 64

# of HPAD’s ........................................ 64

Password Settings .................................. 64

30.10.EX O&M Manual

Summary of Contents for MC3 35.00.EX






































































Search results

Summary of Contents for MC3 35.00.EX

Reviews:

MERRICK MC3 35.00.EX, Operation And Maintenance Manual, Page: 4 / 69

Search results

Summary of Contents for MC3 35.00.EX

Reviews: