manualshive.com logo in svg

MERRICK MC3 35.00.EX, Operation And Maintenance Manual, Page: 56 / 69

Share
Download
MERRICK MC3 35.00.EX Operation And Maintenance Manual Download Page 56

 

 

At this point, the proposed change to the 

Scale Factor

 will be shown. If you wish to 

accept the new value push 

Accept

 button, otherwise, push 

Cancel

 to abort the test. 

E-Cal Factor Procedure 

This procedure will update the 

ECAL Liveload

 parameter, using current 

Scale Factor

. In 

other words, it is the reverse of the 

E-Cal Procedure

. It should only be run after a 

material or weight procedure has been completed, followed by emptying the hopper and 
performing a 

Zero Procedure

. The purpose is to correct the calculated 

ECAL mV/V

 

parameter so that it is based on better calibration procedures. If you later run an E-Cal 
Procedure, you will get more accurate results. 

To run an E-Cal Factor procedure, select this option from the Calibration menu. From this 
point on, the test runs just like the E-Cal Procedure. The 

ECAL mV/V

 parameter will be 

adjusted. No change is made to the Scale Factor. The calibration of the feeder is not 
affected. 

Analog Input Procedure 

This procedure allows you to calibrate the two high-resolution analog inputs 1 and 2. You 
must be able to set the signals at the source to do this. 

 

Press the number of the analog input to calibrate. 

 

Set the signal at the source to represent zero value, typically 4 mA. The live counts will 
vary accordingly.  Since the nominal full scale of the high resolution analog input A/D 
converter in 1,000,000 counts, the value you see should typically be around 200,000 
counts. Push the 

Snap Zero

 button. 

The live value will snap to the New column, Lo row. 

35.00.EX O&M Manual 

 

52 

Summary of Contents for MC3 35.00.EX






































































Reviews:

No comments