manualshive.com logo in svg

MERRICK MC3 35.00.EX, Operation And Maintenance Manual, Page: 51 / 69

Share
Download
MERRICK MC3 35.00.EX Operation And Maintenance Manual Download Page 51

 

 

Calibration Menu 

You may run any of the calibration procedures when the feeder is the Idle state. The 
hopper should typically be empty. The only two meaningful procedures with material in 
the hopper are Weight Procedure and Material Procedure. If the 

Allow Calibr

 logical 

input is Off you will not be able to accept any results. 

Zeroing Procedure 

The purpose of the 

Zeroing Procedure

 is to have zero weight indication when the 

hopper is empty. The 

Zero Weight

 parameter is updated. The hopper must be empty, 

and preferably cleaned when you perform this procedure. 

 

When you push 

Start

, The controller will take the Stable Weight as the new 

Zero Weight

. 

If you do not wish to run the Zeroing Procedure, push the 

Cancel

 button to return to the 

Calibration Menu. However, if you are ready to begin the 

Zeroing Procedure,

 push 

Start

. 

The display will show the elapsed time of the test and an indication on the stability of the 
scale. 

 

When the procedure is complete the screen will show the current and new 

Zero Weight

 

values, as well as the change in the 

Zero Weight

 value as a percent of 

Design Weight

. 

If you wish to accept the new 

Zero Weight

 value, push 

Accept

. Otherwise, push

 Cancel

. 

Pushing either button will return you to the calibration menu. 

35.00.EX O&M Manual 

 

47 

Summary of Contents for MC3 35.00.EX






































































Reviews:

No comments