manualshive.com logo in svg

MERRICK MC3 35.00.EX, Operation And Maintenance Manual, Page: 60 / 69

Share
Download
MERRICK MC3 35.00.EX Operation And Maintenance Manual Download Page 60

 

 

Forcing a Parameter Reset 

It is possible to invoke the Parameters Crash Screen at controller boot by the upper left 
and right touch-pads on the screen during the boot-count-down. 

 

Ram Reset Touch-pads 

You can then reset all parameters to factory default. If you see a fatal error crash screen 
before the count-down starts, press and hold the touch-pads, and then turn the controller 
power on. The boot sequence will then go directly to the crash screen. 

DIAGNOSTIC MENUS 

Pushing the 

Diag Menu

 button in the Action menu takes you to the Diagnostics Menu. 

 

Diagnostic Menu 

It is usable for troubleshooting. It is not necessary to access these menus under normal 
operating conditions. 

HPAD Diagnostics 

HPAD stands for “High Performance Analog to Digital converter”. It is the board in the 
MC³ that takes the Load Cell signal as input and produces a digital value (Counts) as 
output. This screen helps you diagnose weight indication related problems. 

 

HPAD Diagnostics 

Counts:

 

HPAD output counts. With default HPAD scaling settings, 0 – 
1,000,000 corresponds to 0 – 3 mV/V relative output of the load cell. 
A value below 255 will turn on the 

LoadCell Underl

 logical output. A 

value above 1048320 will turn on the 

LoadCell Overl

 logical output. 

35.00.EX O&M Manual 

 

56 

Summary of Contents for MC3 35.00.EX






































































Reviews:

No comments