manualshive.com logo in svg

MERRICK MC3 35.00.EX, Operation And Maintenance Manual, Page: 6 / 69

Share
Download
MERRICK MC3 35.00.EX Operation And Maintenance Manual Download Page 6

 

INTRODUCTION 

SAFETY 

The Merrick MC³ Controller is used for the control of process weighing equipment. To 
insure personnel safety please read the following instructions and precautions carefully.  

In General 

1. 

Observe all standard precautions that pertain to moving machinery. 

2. 

Observe all standard precautions that pertain to electrical drives and electrical 
controls. 

3. 

Pay particular attentions to special notes and precautions that appear throughout 
this manual. 

4. 

Please read and familiarize yourself with this entire manual before attempting 
service or repair of the Merrick MC³ Controller. If you have any questions or 
problems please call the Merrick Service Department for assistance. 

Electrical Precautions 

1. 

Before undertaking work on the electrical system, the drives, or the Controller, 
open the main-disconnect switches and lock boxes. Work should never be 
performed on the Controller with power on the unit.  It is recommended to 
disconnect the power from the controller before attempting any service 
procedure. 

2. 

Verify that all grounds that are called for on the wiring diagrams are in place and 
are securely connected. Proper grounding not only helps insure your personal 
safety, but also is necessary for the proper operation of the controller.  

3. 

If it is necessary that you must work in or near areas of live high voltage, always 
keep one hand clear of the machine, the cabinet, or any other conductors to 
avoid the possibility of electrical shock traveling across your chest. 

4. 

NEVER impair or disable the function of a fuse or a circuit breaker. 

IF YOU ARE IN DOUBT ABOUT ANY PROCEDURE, CONTACT THE MERRICK 
SERVICE DEPARTMENT. 

RELATED PUBLICATIONS 

You will find related publications regarding MC³ controller hardware, internal register 
database information and industrial networking capabilities at the support web site at 

http://www.merrick-inc.com/mct

. In the rest of the manual, this is referred to as [MCT]. 

MANUAL CONVENTIONS 

NOTE:

   

Any additional information that may be useful follows the note marker. 

CAUTION:

 

Be careful, certain settings may cause problems.

 

WARNING:

 

Follow the directions prescribed in the warning.  Serious problems can occur if the 
recommendations are not followed. 

R[254] This is a register reference to a parameter, in this case register number 254. 
Some parameters are rarely used or considered to be experimental. They can be 
inspected or changed, using the Register Editor. See page 64. 

35.00.EX O&M Manual 

 

2 

Summary of Contents for MC3 35.00.EX






































































Reviews:

No comments