manualshive.com logo in svg

MERRICK MC3 35.00.EX, Operation And Maintenance Manual, Page: 21 / 69

Share
Download
MERRICK MC3 35.00.EX Operation And Maintenance Manual Download Page 21

 

 

New Setpoint Method accepted 

To prevent changes to the setpoint method, you can turn the Logical Input 

Lock SP 

Method

 on. See Logical Inputs on page 35. This disables the ability to change the 

Setpoint method, and removes the setpoint method button. 

Manual Setpoint Method 

 

Manual Speed Setpoint 

The 

Manual Speed

 setpoint method allows you to directly control the Speed Demand 

output signal, in percent. The 

Start/Stop

 button allows you to directly control the 

Fdr 

Drive Enabl

 logical output to start and stop the drive. See Logical Outputs on page 39. 

The Manual Speed setpoint method is useful at Startup, when adjusting the Feeder Drive 
or when troubleshooting. 

NOTE:

   

You can only select the Manual Speed method when the controller is in the Idle state. 

ACTION MENU 

Pushing the 

Action Menu

 button anywhere takes you to the Action Menu. This is where 

you start and stop the feeder and perform maintenance tasks. 

 

Action Menu 

This is what the Action Menu looks like when the feeder is in the Idle state, waiting for a 
Start Batch command. 

Batch Control Buttons 

The 

Start Batch, Clear Batch, Start Fill and Start Cleanout

 buttons used for locally 

controlling the feeder. The buttons are context sensitive, meaning that their availability 
and caption changes with the feeder state. See Feeder States on page 6. There are also 
logical inputs to remotely perform these functions. See Logical Inputs on page 35. 

35.00.EX O&M Manual 

 

17 

Summary of Contents for MC3 35.00.EX






































































Reviews:

No comments