MERRICK MC3 35.00.EX Operation And Maintenance Manual Download Page 43 | Manualshive

Page: 43 / 69

MERRICK MC3 35.00.EX Operation And Maintenance Manual Download Page 43

Select Column

This button switches the active scroll area between the Physical and
Logical columns. First select the physical output you want to work
with, using the Up and Down arrow buttons. Then push the

Select

Column

button to map it to a physical output, again using the Up and

Down arrow buttons.

Invert Off/On

This button inverts the logic of the physical output. For example, if

Rack 1 Output 1

is mapped to the logical output

Fault

, you would

typically invert that output, so that the output contact is closed when
there is no fault. An inverted output will have a

1

in the

IV

column.

The button is only available when you have the Physical Output
selected, since the Invert property is associated with the physical
output.

Force None/Off/On

This button toggles the

FC

indication through Forced On

1

, Forced

Off

0

or no Force

-

. There will be a blinking indication on the Main

Screen if forces are present. The button is only available when you
have the Physical Output selected, since the Force property is
associated with the physical output.

Alarming

Since un-mapped logical outputs are not visible in this screen, this
button takes you to another screen where you can set the Faults and
Warnings properties for all logical outputs, both mapped and un-
mapped.

WARNING:

If you have made changes to the mapping, press

Accept

before pressing

Alarming

. If

you don’t, the mapping changes will be lost.

Set the Warning and Fault properties for all Logical Outputs by
scrolling to the output with the up and down arrows and then push the

Select F/W

button. When you are done, push the

Return

button.

Accept

When you are done with your Logical Outputs configuration, push this
button to make your configuration changes permanent. The button is
only available when you have the

Logical Output

column selected.

Esc

Takes you back to the Inputs and Outputs Setup Screen. If you push
this button without first pushing the

Accept

button, The Digital

Outputs configuration will be restored to the condition it had when you
entered this menu.

Logical Outputs

Logical Output

Description

35.00.EX O&M Manual

39

«
...
41
42
43
44
45
...
»

Summary of Contents for MC3 35.00.EX






































































Reviews:

No comments