manualshive.com logo in svg

MERRICK MC3 35.00.EX, Operation And Maintenance Manual, Page: 48 / 69

Share
Download
MERRICK MC3 35.00.EX Operation And Maintenance Manual Download Page 48

 

 

Communications Settings 

For Baud Rate, Data Bits, Stop bits and Parity parameters, simply pushing the button for 
the corresponding parameter will toggle through the available settings. 

Comm 1 Numeric 

For details, refer to Modbus and Scalenet documentation at

 [MCT]

. 

Param Meaning 

Controller # 

Controller Number for ScaleNet, Node Number for Modbus 

Start Char 

ASCII code for ScaleNet telegram start character. Default 10 (LF) 

End Char 

ASCII code for ScaleNet telegram end character. Default 13 (CR) 

Comm Timeout 

Timer for Ser Com Lost output. A value of 0 will disable the timing, 
and the logical output 

Ser Comm Lost

 will never go on. 

Com Protocol 

Set to 0 for ScaleNet 
Set to 1 for Modbus ASCII 
Set to 2 for Modbus RTU 

Write Prot 

Write protection bits for Common Interface Table (CIT) variables. 
Decimal representation. 

Word Order 

Floating point representation word order bit pattern for CIT. 

Int/Frac FP 

Integer Fraction  floating point representation bit pattern for CIT. 

Tag Reg 1 – 5 

MC³ register number tagged. 

Comm 2 Numeric 

For details, refer to DF-1 documentation at 

[MCT]

. 

Param Meaning 

Prtr/0 DF1/1 

Set to 0 for Comm2 to be used for a serial printer 
Set to 1 for Comm2 to be used for DF-1 communications 

DF-1 Timeout 

Timer for DF-1 Comm Lost output. A value of 0 will disable the timing, 
and the logical output 

DF-1 Timeout

 will never go on. 

DF-1 uses BCC 

Set to 0 for CRC error check 
Set to 1 for BCC error check. 

Write Prot 

Write protection bits for Common Interface Table (CIT) variables. 
Decimal representation. 

Word Order 

Floating point representation word order bit pattern for CIT. 

Int/Frac FP 

Integer Fraction  floating point representation bit pattern for CIT. 

Tag Reg 1 – 5 

MC³ register number tagged. 

35.00.EX O&M Manual 

 

44 

Summary of Contents for MC3 35.00.EX






































































Reviews:

No comments