manualshive.com logo in svg

MERRICK MC3 35.00.EX, Operation And Maintenance Manual, Page: 59 / 69

Share
Download
MERRICK MC3 35.00.EX Operation And Maintenance Manual Download Page 59

 

 

Parameter Compatibility Crash 

   Firmware Version: 56, 67

  

Firmware ID and Version ID of 35.00.EX.C. 

Parameters Version: 56, 66 

 

Firmware ID and Version ID before upgrade. 

 

In this case, you should reset the parameters (

Reset Ram

) to factory default (unless 

instructed otherwise by Merrick Customer Support), and then enter the new parameters 
either from the spec sheet or from a prepared parameters file, using WinMerik. 

Fatal Error Crash 

The crash screen caused by a fatal error can occur anytime, including controller boot. 
The crash screen looks something like this 

 

Example of Fatal Error Crash 

Fatal Error 

Indicates the nature of the crash.

 

Please Report

 

A fatal error should always be reported to Merrick Technical Support. 

The last line normally will contain additional information. I this example, an attempt was 
made to perform a division with a zero value in the denominator. 

The most common reason is that an invalid parameter has been entered into the 
controller by means of serial communications or by using the Register Editor. If you have 
been working with communications or using the register editor recently, you may have an 
idea of what happened. 

The only way out of this situation is to cycle the MC³ power. This may restore controller 
operation, but the most likely scenario you will see a new Crash Screen at controller 
boot. If that is the case, you can attempt forcing a Reset to Factory Default, and then re-
enter all controller parameters. See below. 

35.00.EX O&M Manual 

 

55 

Summary of Contents for MC3 35.00.EX






































































Reviews:

No comments