manualshive.com logo in svg

MERRICK MC3 35.00.EX, Operation And Maintenance Manual, Page: 67 / 69

Share
Download
MERRICK MC3 35.00.EX Operation And Maintenance Manual Download Page 67

 

35.00.EX… 

This line identifies the firmware application name, build (release) 
date, application identification number and version identification 
number. 

Hours On

 

How many hours the MC³ has been powered up, accumulated. 

Hours Ran

 

How many hours the feeding device has been running, accumulated. 
Reset to zero by pushing 

Clear Hours Ran

 button

. 

Bd-… 

There is no meaningful information in this line. 

Modbus Diagnostics 

There are two diagnostics screen available for troubleshooting Modbus communications. 

  

   

Modbus Troubleshooting and monitoring 

One screen displays communication related statistics, and one displays data in the 
Common Interface Table. For details, see 

[MCT]

. 

DIAGNOSTIC SETTINGS 

This selection takes you to the Diagnostic Settings menu. The menu is password 
protected, with default password 1030. Any modifications to parameters in the Diagnostic 
Settings are potentially dangerous. It is quite possible to crash the application from here. 

 

Diagnostic Settings 

HPAD Settings 

You can change the default HPAD scaling here, to improve live load resolution or to 
make a somewhat overloaded 3 mV/V load cell operational. Use in conjunction with the 
HPAD Diagnostics screen, page 56. 

CAL 

This value is used by the HPAD Converter to simulate load on the load cell during an 
Electronic Calibration, and is normally zero. A non-zero setting will inject a positive load 
cell signal before the A/D converter. The injected signal is 0.2 mV/V times the setting. In 
the rare occasion of negative dead load, non-zero value can be entered. 

ZERO 

This value is used by the HPAD Converter to electronically remove dead load from the 
load cell signal. This allows the HPAD to operate at a higher Gain and achieve better 
resolution when measuring the load cell signal. A non-zero setting will inject a negative 

35.00.EX O&M Manual 

 

63 

Summary of Contents for MC3 35.00.EX






































































Reviews:

No comments