3-22
Revised 08.2021
Operator’s Manual: 405 SLD Seed Express
™
Bulk Seed Tender
®
®
The indicator mark and the alignment plate
must be aligned for the conveyor arm locking
pin to engage.
- This pin locks the inner and outer tubes of
the conveyor arm together.
- These two tubes must be locked together
before releasing the conveyor hitch
receiver (ball coupling).
- If tubes are not locked together, the inner
tube will slide down inside the outer tube
and will not come out of the ball catch.
ELECTROCUTION HAZARD
Keep away from power lines.
• Be aware of your surroundings when raising
or lowering the auger tube.
• Maintain at least 20 feet between the
equipment and any electrical hazard.
• Contact with electricity can result in serious
personal injury or death.
6. Swing the conveyor.
7. Align the triangular indicator on the conveyor
pivot plate with the alignment plate on the
frame, as shown.
39
7. Using the remote control unit or the control
panel, slightly raise the conveyor from the
transport position.
MMG-00322b
8. Using the remote control unit or the control
panel, rotate conveyor to align the triangular
indicator on the conveyor pivot plate with the
alignment plate on the frame, as shown.
MMG-00324
NOTICE
The indicator mark and the alignment plate must be
aligned for the conveyor arm locking pin to engage.
This pin locks the inner and outer tubes of the
conveyor arm together. These two tubes must be
locked together before releasing the conveyor hitch
receiver (ball coupling). If the tubes are not locked
together, the inner tube will slide down inside the
outer tube and will not come out of the ball catch.
9. To lock the conveyor arm tubes together, pull
the handle of the lock pin outward slightly and
rotate it 90° counterclockwise.
MMG-00328
1
2
39
7. Using the remote control unit or the control
panel, slightly raise the conveyor from the
transport position.
MMG-00322b
8. Using the remote control unit or the control
panel, rotate conveyor to align the triangular
indicator on the conveyor pivot plate with the
alignment plate on the frame, as shown.
MMG-00324
NOTICE
The indicator mark and the alignment plate must be
aligned for the conveyor arm locking pin to engage.
This pin locks the inner and outer tubes of the
conveyor arm together. These two tubes must be
locked together before releasing the conveyor hitch
receiver (ball coupling). If the tubes are not locked
together, the inner tube will slide down inside the
outer tube and will not come out of the ball catch.
9. To lock the conveyor arm tubes together, pull
the handle of the lock pin outward slightly and
rotate it 90° counterclockwise.
MMG-00328
1
2
39
7. Using the remote control unit or the control
panel, slightly raise the conveyor from the
transport position.
MMG-00322b
8. Using the remote control unit or the control
panel, rotate conveyor to align the triangular
indicator on the conveyor pivot plate with the
alignment plate on the frame, as shown.
MMG-00324
NOTICE
The indicator mark and the alignment plate must be
aligned for the conveyor arm locking pin to engage.
This pin locks the inner and outer tubes of the
conveyor arm together. These two tubes must be
locked together before releasing the conveyor hitch
receiver (ball coupling). If the tubes are not locked
together, the inner tube will slide down inside the
outer tube and will not come out of the ball catch.
9. To lock the conveyor arm tubes together, pull
the handle of the lock pin outward slightly and
rotate it 90° counterclockwise.
MMG-00328
1
2
39
7. Using the remote control unit or the control
panel, slightly raise the conveyor from the
transport position.
MMG-00322b
8. Using the remote control unit or the control
panel, rotate conveyor to align the triangular
indicator on the conveyor pivot plate with the
alignment plate on the frame, as shown.
MMG-00324
NOTICE
The indicator mark and the alignment plate must be
aligned for the conveyor arm locking pin to engage.
This pin locks the inner and outer tubes of the
conveyor arm together. These two tubes must be
locked together before releasing the conveyor hitch
receiver (ball coupling). If the tubes are not locked
together, the inner tube will slide down inside the
outer tube and will not come out of the ball catch.
9. To lock the conveyor arm tubes together, pull
the handle of the lock pin outward slightly and
rotate it 90° counterclockwise.
MMG-00328
1
2
Fig 38 - Remote control handset
Fig 39 - Control panel switch
Fig 40 - Align triangle indicator
Fig 41 - Lock conveyor tubes together
8. To lock the conveyor arm tubes together, pull
the handle of the lock pin outward slightly
and rotate it 90° counterclockwise.
