Revised 08.2021
3-23
Operator’s Manual: 405 SLD Seed Express
™
Bulk Seed Tender
®
®
9. Release and push the lock pin inward to lock
the inner and outer tubes of the conveyor
arm together.
- Make sure the pin is fully engaged.
40
10. Release and push the lock pin inward to lock
the inner and outer tubes of the conveyor arm
together. Make sure the pin is fully engaged.
MMG-00329
11. Once the tubes are locked together, rotate
hopper guide handle 90° into the position
shown.
12. Slide the ball coupling out of the conveyor
hitch receiver.
CRUSH
HAZARD
ELECTROCUTION
HAZARD
Avoid contact with overhead power
lines or electrically powered objects.
• Be aware of your surroundings when
raising or lowering conveyor.
• Maintain at least 20 feet between
equipment and any electrical hazard.
• Contact with electricity can result
in serious personal injury or death.
Keep hands and
arms clear of
conveyor tube
when placing it
in storage
position.
Weight of tube
will cause
crushing injuries.
17509
Be observant of overhead power lines or other
electrical hazards.
13. When the ball coupling is free of the conveyor
hitch receiver, lift the bottom of the conveyor
arm over the fender and hold it off the ground
until it is in its final position.
WARNING
If two people are positioning the conveyor arm,
one at the controls and the other holding the
conveyor arm, be extremely careful to prevent
a crush hazard. Do not place any part of your
body between stationary and moving parts.
40
10. Release and push the lock pin inward to lock
the inner and outer tubes of the conveyor arm
together. Make sure the pin is fully engaged.
MMG-00329
11. Once the tubes are locked together, rotate
hopper guide handle 90° into the position
shown.
12. Slide the ball coupling out of the conveyor
hitch receiver.
CRUSH
HAZARD
ELECTROCUTION
HAZARD
Avoid contact with overhead power
lines or electrically powered objects.
• Be aware of your surroundings when
raising or lowering conveyor.
• Maintain at least 20 feet between
equipment and any electrical hazard.
• Contact with electricity can result
in serious personal injury or death.
Keep hands and
arms clear of
conveyor tube
when placing it
in storage
position.
Weight of tube
will cause
crushing injuries.
17509
Be observant of overhead power lines or other
electrical hazards.
13. When the ball coupling is free of the conveyor
hitch receiver, lift the bottom of the conveyor
arm over the fender and hold it off the ground
until it is in its final position.
WARNING
If two people are positioning the conveyor arm,
one at the controls and the other holding the
conveyor arm, be extremely careful to prevent
a crush hazard. Do not place any part of your
body between stationary and moving parts.
Fig 42 - Push in locking pin
Fig 43 - Hopper guide handle
10. Once the tubes are locked together, rotate
hopper guide handle 90°.
- See illustration for the correct position.
11. Use the toggle switch on the handle to
operate the actuator that opens and closes
the hitch receiver.
- Press and hold the toggle switch downward
to open.
- Refer to decal #10379 for instructions.
12. Slide the ball coupling out of the conveyor
hitch receiver.
Fig 44 - Toggle switch
40
10. Release and push the lock pin inward to lock
the inner and outer tubes of the conveyor arm
together. Make sure the pin is fully engaged.
MMG-00329
11. Once the tubes are locked together, rotate
hopper guide handle 90° into the position
shown.
12. Slide the ball coupling out of the conveyor
hitch receiver.
CRUSH
HAZARD
ELECTROCUTION
HAZARD
Avoid contact with overhead power
lines or electrically powered objects.
• Be aware of your surroundings when
raising or lowering conveyor.
• Maintain at least 20 feet between
equipment and any electrical hazard.
• Contact with electricity can result
in serious personal injury or death.
Keep hands and
arms clear of
conveyor tube
when placing it
in storage
position.
Weight of tube
will cause
crushing injuries.
17509
Be observant of overhead power lines or other
electrical hazards.
13. When the ball coupling is free of the conveyor
hitch receiver, lift the bottom of the conveyor
arm over the fender and hold it off the ground
until it is in its final position.
WARNING
If two people are positioning the conveyor arm,
one at the controls and the other holding the
conveyor arm, be extremely careful to prevent
a crush hazard. Do not place any part of your
body between stationary and moving parts.
Fig 45 - Ball coupler
