manualshive.com logo in svg

Mercury 1.7 MI, Manual

Share
Download
Mercury 1.7 MI Manual Download Page 224

STORAGE

SECTION 6

Page 92

CMD-3967823 / 90-865237030   OCTOBER 2003

CE499

Cold Weather Or Extended Storage

IMPORTANT: Cummins  MerCruiser Diesel strongly recommends that this service

should be performed by an authorized Cummins  MerCruiser Diesel  dealer /

distributor. Damage caused by freezing IS NOT covered by the Mercury MerCruiser

Limited Warranty.

CAUTION

Seawater section of cooling system MUST BE COMPLETELY drained for winter

storage, or immediately after cold weather use, if the possibility of freezing

temperatures exist. Failure to comply may result in trapped water causing freeze

and/or corrosion damage to engine. Damage caused by freezing is NOT covered by

the Cummins MerCruiser Diesel Limited Warranty.

IMPORTANT: Cummins MerCruiser Diesel recommends that propylene glycol

antifreeze (a nontoxic and environmentally safe) antifreeze be used in the seawater

section of the cooling system for cold weather or extended storage. Ensure that the

propylene glycol antifreeze contains a rust inhibitor and is recommended for use in

marine engines. Follow the propylene glycol manufacturer’s recommendations.

CE501

Preparing Your Power Package For Storage

IMPORTANT: If the boat has already been removed from the water, before starting the

engine a source of water must be supplied to the seawater pump inlet. Follow all

warnings and flushing attachment procedures stated in SECTION 5 - Flushing The

Seawater System.

CAUTION

Overheating from insufficient cooling water will cause engine and drive system

damage. Ensure that there is sufficient water always available at water inlet

openings during operation.

1. Supply cooling water to the seawater pump inlet.
2. Start the engine and operate until it reaches normal operating temperature.
3. Stop the engine.
4. Change the engine oil and oil filter.
5. Start the engine and operate for about 15 minutes. Check for oil leaks.
6. Flush the seawater cooling system. Refer to 

Section 5 - Flushing The Seawater

System 

procedure shown earlier in this manual.

INDEX

Summary of Contents for 1.7 MI

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands