McDATA Sphereon 4500 User Manual Download Page 169

Page: 169 / 216

Product Manager Messages

A-9

Product Manager Messages

Message

Could not find firmware file.

Description

The selected file is not a firmware file.

Action

Obtain a valid firmware file from your service representative.

Message

Could not remove dump files from server.

Description

Dump files could not be removed from server. Link may be down or
switch may be busy.

Action

Retry the operation later. If the condition persists, contact support
personnel.

Message

Could not stop port diagnostics.

Description

Port diagnostics could not be stopped. Link may be down or switch
may be busy.

Action

Retry the operation later. If the condition persists, contact support
personnel.

Message

Could not write firmware to flash.

Description

Firmware could not be written to flash memory.

Action

Try again. If problem persists, contact support personnel.

Message

CUP name and port name are identical.

Description

Within the address configuration, one or more of the port names are
the same as the CUP name.

Action

Make sure all names are unique for the ports and CUP name.

Summary of Contents for Sphereon 4500

























































































































































































































Search results

Summary of Contents for Sphereon 4500

Reviews:

Related manuals for Sphereon 4500

Brands by name

Popular brands

McDATA Sphereon 4500, User Manual

Search results

Summary of Contents for Sphereon 4500

Reviews:

Related manuals for Sphereon 4500

Brands by name

Popular brands