background image

KJM MANDÍK 

 Detailed operating instructions

 

        

M&C KJMPNO 07/2022 

MANDÍK, a.s., 

www.mandik.cz

    

 

52 

of  these  contacts,  the  control  monitors  the  status  of  the  fire  dampers  and  decides  on  the 

operation of the air conditioning unit. The monitoring of the dampers can also be carried out using 

the  THC24-B  electronic  relay.  Up  to  8  fire  dampers  can  be  monitored  in  the  standard 

configuration. 

The method of monitoring and the type of fire damper is determined in the configuration. 

For motorised dampers, the open position contact is monitored during start-up and operation of 

the  unit.  The  damper  must  be  closed  (contact  open)  when  the  unit  starts  and  open  (contact 

closed) after the 

TimeOpen 

time has elapsed.  

If,  while  the  unit  is  running,  the  contact  indicating  an  open  damper  on  any  fire  damper 

opens (damper closes), then the AC unit will shut down immediately and a failure of that particular 

fire damper will be indicated.  

 

FireDamper

 (

Undefined

/

Close

/

Open

/

Err

– information about the position of the fire damper.  

 

Undefined

  – 

damper  is  currently  moving  between  the  extreme  open  and  closed 

positions. 

 

Close

 – 

damper is in the closed position.

 

 

Open

 – 

damper is in the open position.

 

 

Err

 – 

damper is not in the expected position.

 

 

TimeOpen

  (130  s) 

–  time  it  takes  for  the  motorised  fire  damper  to  move  from  the  closed 

position to the open position. Applies only to configuration options 

Mot1c

 and 

Mot2c

 

UnitStopFlapClose

  (

Open

/

Close

–  determines  the  position  of  the  damper  when  the  air 

conditioning unit is off. Only applies to the 

Mot2c

 

and

 THC

 configuration options. 

 

Open

 – 

when the A/C unit is off, the power to the damper actuators is not turned off 

and the dampers remain open. 

 

Close

 – 

when the AC unit is off, the power to the damper actuators is turned off and 

the dampers are closed.

 

 

Freecooling 

6.18

Freecooling is used to freely ventilate the room and lower the temperature in it, using the 

coolness  of  the  outside  air.  It  is  mainly  used  at  night.  Freecooling  can  be  triggered  by  a  custom 

time  program,  by  an  external  contact  or  manually  from  the  controller  display.  For  proper 

freecooling  operation,  sensors  for  outdoor,  supply  and  room  temperatures  must  be  configured. 

Summary of Contents for Climatix




















































































Reviews: