background image

KJM MANDÍK 

 Detailed operating instructions

 

        

M&C KJMPNO 07/2022 

MANDÍK, a.s., 

www.mandik.cz

    

 

15 

than  the  non-sensitivity,  then  a  damper  failure  may  be  indicated  and  consequently  the 

component with that damper or the entire AC unit may shut down.

 

 

Temperatures 

6.1

 

This  menu  contains  information  about  the  measured  temperatures  according  to  the 

settings in the configuration. The location of the temperature sensors in the air handling unit and 

air ducts can be seen in Figure 2.  

 

Legend:  

T1 – 

Outdoor

 (ODA)  

 

T4 – 

Preheat

 – 

after 1st heating

 

T7 – 

Room

 

T2 – 

Inlet

 

 

 

 

T5 – 

Reheat

 – 

before 2nd heating

    T8 – 

Extract

 (ETA) 

T3 – 

Supply

 

Recuperation

   

T6 – 

Supply

 (SUP) 

 

 

T9 – 

Extract

 

Recuperation

 

T10 – 

Exhaust

 (EHA

Fig. 2 - Temperature sensor locations 

 

Following  are  the  descriptions  of  every  temperature  sensor,  including  installation  methods 

and other related settings: 

 

Room

 

–  if  configured,  the  sensor  should  be  placed  in  the  room  that  is the target  of the  air 

conditioning so that the measured temperature is not affected by any local influences, such 

as radiators, sunlight through a window, etc. If not configured, it can be replaced by a supply 

Summary of Contents for Climatix




















































































Reviews: