![background image](http://html1.mh-extra.com/html/manatec/fox-3d-smart-mobile-pt/fox-3d-smart-mobile-pt_service-manual_4409014042.webp)
Ref.: 3DWA - SM Ver.1.8
39
In AVH model, A Distribution panel is located at the rear side of cabinet for distributing
the Power from Interface box to Desktop computer and peripherals.
The ON/OFF switch provided in the Panel can be used to switch OFF complete power
to the system after shutdown of the PC.
Following Control fuse is available in Distribution panel as described below:
Control fuse - F3 is provided for protection of PC peripherals
Specifications
– 5A, ½”, Slow blow type Glass fuse
Fuse will blow in 5 seconds (max.) for maximum current of 5A
1
2
3
4
5
6
Fig. 42
Sl.
No.
Description
Sl.
No.
Description
1 ON/OFF DPST switch
4 AC output for Monitor
2 AC input for Distribution panel
5 AC output for Printer & Speaker
3 AC output for PC
6 Fuse (F3) for PC & Peripherals
5.2.1.
EMI FILTER BOARD
(applicable only for PT / VH / In-Lift models)
The EMI Filter board receives 230VAC or 110VAC and filters the electrical
noise and clean AC power is delivered to the PC Peripherals. Refer the Wiring
diagram (Chapter 10.2) for the electrical power distribution.
5.2.2.
SMPS
The 60W SMPS generates 12VDC with 5ampere output. It is a wide operating
voltage SMPS ranging from 90V to 270VAC / 47Hz - 63Hz input. The 12V is
then distributed to Cooling fan, IR LED board and LED Driver & Hub board.
5.2.3.
MOTOR CONTROL BOARD
(applicable only for AVH model)
The Board contains EMI filter and Motor forward/reverse control section. The
EMI Filter section receives 230VAC or 110VAC and filters the electrical noise
and clean AC power is delivered to the PC Peripherals. Refer the Wiring
diagram (Chapter 10.2) for the electrical power distribution.
The Motor control section turns On/Off the respective Triacs for forward &
reverse direction of Motor. Also it distributes power to Monitor, Transformer &
SMPS.
5.2.4.
MOV BOARD
(applicable only for AVH model)
The Metal Oxide Varistors are used between Line & Neutral to protect the
system against I/P Over voltage / Surge / Spike etc.
5.3.
TARGET PLATE
The Target plate is a specially designed accessory mounted with Wheel bracket. A
Bubble Spirit level is fixed with it to ensure the vertical position. The Target plates are
positioned with Wheel bracket in such a way that the patterned reflecting media on
Target plate surface will reflect the IR light received from the IR Light source.
Summary of Contents for Fox 3D Smart Mobile PT
