![background image](http://html1.mh-extra.com/html/manatec/fox-3d-smart-mobile-pt/fox-3d-smart-mobile-pt_service-manual_4409014100.webp)
Ref.: 3DWA - SM Ver.1.8
97
Sl.
No.
Error
Causes
Remedies
Jerk during Runout.
Undulation in the platform
Correct it
Defective wheel bracket
Replace the wheel bracket to
confirm
Calibration shaft is bent or
distorted
Calibrate with proper kit
On vehicle side,
Make length of tie rods equal
Check for worn out rear axle
mountings
Check tyre pressure
If Vehicle aligned with
Uneven tyre wear
DESKTOP COMPUTER & PERIPHERALS
Sl.
No.
Error
Causes
Remedies
1
When System is
switched ON, no beep
sound and No display
Power socket problem or
loose connection in the Power
socket plug point
Insert the equipment‟s Power
cord to another Plug point‟s
power socket & check it
Still problem persists
UPS may be defective. i.e, No
output from the UPS
Connect a Test lamp at the
output socket of UPS and ensure
whether UPS is OK. If not
replace the UPS
Loose connection in Fuse /
Fuse may be blown off.
Check the status of Fuse and
replace it
All the external
parameters have been
checked. But the display
problem remains as it is
ON/OFF Switch or Power
supply board may be faulty
Get the problem solved through
Service Engineer
2
When equipment is
switched ON, only Audio
sound is noticed. But no
display in Monitor
Monitor may be switched OFF
or Power supply to Monitor
may got disconnected.
Switch ON the Monitor and
Check the Power LED is ON. If
not, replace the Power cord.
Monitor Power LED
blinking in Standby
mode. But no display
Loose connection in the
Monitor data cable
Switch OFF the system, remove
the 15 Pin data cable and
reconnect it to the system with
correct polarity
No loose connection in
Data cable. Still the
display problem persists
Monitor may be defective
Replace a monitor from other
computer and check for it
Computer‟s Internal system
may be defective
Get the problem solved through
Service Engineer
3
Electrical Shock
observed in the system
No Earthing or loose contact
in the Earthing point of switch
board
Get the problem solved through
Qualified personnel
Earthing terminal in Power
cord may have intermediate
cut
Replace the Power cord
Summary of Contents for Fox 3D Smart Mobile PT
