![background image](http://html1.mh-extra.com/html/manatec/fox-3d-smart-mobile-pt/fox-3d-smart-mobile-pt_service-manual_4409014102.webp)
Ref.: 3DWA - SM Ver.1.8
99
Sl.
No.
Error
Causes
Remedies
3
Camera (either LH / RH)
disconnected during operation
USB cable from Hub Board
to Camera might have
contact problem
If one of the devices is
found disconnected in
Device Manager, check for
USB Cable. Interchange
the USB cable to confirm.
Or, replace the USB cable
USB cable from PC to HUB
board may be faulty
Check & replace
Camera Driver File
Corrupted
Go to
“Device Manager”
screen by selecting
“Properties” from the right
click options of
“Computer”
from Start menu. Check
whether the driver is
loaded. If
symbol is
displayed, remove & re-fix
USB cable. Driver will load
automatically. Else,
reinstall Alignment SW
Camera failure
Replace with new camera
4
„X‟ mark over the respective
Target plate image / sides
Camera failure
Replace with new camera
Target plate Line-Of-Sight
obstructed
Remove the obstruction
Input supply to IR LED
board is <9VDC
Adjust the respective
Trimpot in LED Driver &
Hub board to set the
required voltage (9VDC)
Input supply to IR LED
board is >9VDC
Target plate not clean
Clean the Target plate
Direct Sun light falls on
Camera or Target Plate
Avoid direct sunlight falling
on Target plate
Target plate physical
damage
Replace the respective
Target plate
5
Unhandled exception error
Calibration file may be
corrupted due to improper
shut down
Restore the following files
from back up.
a. Calib_3D_L.mdb
b. Calib_3D_R.mdb
c.
Align_3d.mdb
If problem still exists, re-
install the Alignment SW
6 Camera file mismatch
Respective camera
calibration files are not
installed
Install Camera calibration
files from the CD provided
or contact the Manufacturer
11.4.
MIS-ALIGNMENT TROUBLE SHOOTING
Sl.
No.
Error
Causes
Remedies
1
Car pulling
towards one
side
Misaligned Rear axle (ie.,
unequal Rear Toe).
Rear axle is not perpendicular
to Geometric Centre Line
Check the Rear suspension for worn out
control arm bushings or sagged springs
Setback
Check the position of Front wheels are in line
Improper Camber setting.
Car pulls sideway with more
positive Camber
Check for worn out ball joints or control arm
bushings and sagged or broken springs
Uneven tyre pressure.
Car pulls sideway with low
inflation
Check both tyres are with same pressure
Summary of Contents for Fox 3D Smart Mobile PT
