Mamiya 645 AFD III Instructions Manual Download Page 59

Page: 59 / 68

6. Press the Button for about two seconds to register
the value.

After the value is registered, the shutter speed and aperture cannot be changed by

turning the Front or Rear Dials.

If you operate the Electronic Dial with Electronic Dial Lock ON, L blinks in the Main

LCD to affirm that the lock is functioning correctly.

Releasing Electronic Dial Lock

Repeat Steps 1 - 4, turn the Front or Rear Dial to select OF, and press the Button for
about two seconds to register the change.

AF Supplemental Infrared Light Canceling Function

Use this function to deactivate the AF Supplemental Infrared Light.

1. Turn the Shutter Release Mode Selector Lever to
either "S" or "C".

2. Press the Key for about two seconds. The
Main LCD will display Func.

3. Turn the Front or Rear Dial and select AFLE.

4. Press the Key again and turn the Front or
Rear Dial to select OF.

5. Press the Button for about two seconds to
register the change.

Exiting this Function

Repeat Steps 1 - 4, turn the Front or Rear Dial and select On, and then
press the Button for about two seconds to register the change.

Summary of Contents for 645 AFD III





































































Search results

Summary of Contents for 645 AFD III

Reviews:

Related manuals for 645 AFD III

Brands by name

Popular brands

Mamiya 645 AFD III, Instructions Manual

Search results

Summary of Contents for 645 AFD III

Reviews:

Related manuals for 645 AFD III

Brands by name

Popular brands