M A G U I R E P R O D U C T S , I N C .
Edition: August 5, 2014
7
W E I G H S C A L E B L E N D E R
®
SECTION 1 – BLENDER STARTUP
Getting Started – Read this page!
THE NEXT SECTIONS OF THIS MANUAL WILL GUIDE YOU, STEP BY STEP, TO A
SUCCESSFUL STARTUP.
IT WON'T TAKE LONG; SO.... PLEASE, DON'T SKIP AHEAD.
HERE ARE THE STEPS YOU WILL FOLLOW:
SAFETY HAZARDS - Page 8 ………………………..
TWO HAZARDS exist on this unit: MIX BLADES and SLIDE VALVES. Read
this short sensible page so no one gets hurt.
ASSEMBLY INSTRUCTIONS - Page 12 …………….
Very little assembly is required. But you might as well get it right the first
time. ALSO: Pay attention to the section on WIRING.
CHECK OUT PROCEDURE - Page 17 …………….
This is to see if you did it right. It also will tell if anything was damaged in
shipping.
LOAD CELL CALIBRATION - Page 22 ……………
We already did this. But shipping or rough handling during assembly
sometimes creates load cell problems. If weight readings are not correct,
you MUST recalibrate the load cells.
SETUP OUTPUTS & MATERIAL TYPES - Page 22..
To "TURN ON" a component, it must be designated as to TYPE, either
REGRIND, NATURAL, or ADDITIVE. Each is handled differently by the
MATH routines. The controller MUST know the material TYPE to know what
the setting means. This is IMPORTANT. Be SURE you UNDERSTAND this
section before trying to operate your system.
RATE CALIBRATION - Page 27 ……………………
This is NOT really necessary. But if your system uses non-standard
equipment, you MAY want to do this.
SETTINGS & NORMAL OPERATION - Page 28 …
From this point forward, operating your system is a snap. This section tells
you just how simple it is and exactly what to expect under normal operating
conditions.
SPECIAL FEATURES - Page 29 …………………...
Your system can do much more then you may know. This page reviews
briefly some of the added features that are available to you and where in this
manual you can find them.
PROCEED TO: SAFETY HAZARDS NEXT PAGE
Summary of Contents for Weigh Scale Blender WSB
