Magnetek GPD 333 Technical Manual Download Page 9 | Manualshive

Page: 9 / 81

background image

1.3.1 Installation or Removal of Digital Operator.

The GPD 333 is shipped with the
status panel (shown at right) in
place. If programming of con-
stants is to be performed, or if
local control via keypad entry is
desired, the optional Digital
Operator, Model DS039, must be
installed.

1.

Ensure that input power is

not applied to the GPD 333, and
the "CHARGE" lamp is off.

2.

Remove the GPD 333 access

cover (see Figure 1-2).

3.

Press down on the terminal marker lever (see View B in

Figure 1-1.1), and lift upward on the bottom edge of the status
plate to remove it from the mounting recess.

4.

Locate the Digital Operator in the mounting recess, as

shown in View A of Figure 1-1.1, and press until it snaps into
place.

5.

Reinstall the access cover.

If, after constant programming, the drive is not to be operated
or monitored via the Digital Operator, it may be removed with-
out affecting operation. Perform the same procedure as above
to remove the Digital Operator and reinstall the status plate.

1.1

Status Plate

efesotomasyon.com - Yaskawa ac drive,servo motor

«
...
7
8
9
10
11
...
»

Summary of Contents for GPD 333


















































































Reviews:

No comments

Related manuals for GPD 333

Brand: Farris Engineering Pages: 12

Brand: Eastern Times Technology Pages: 4

Brand: Vacon Pages: 18

Brand: Lawler Pages: 5

Brand: D-Link Pages: 113

Brand: D-Link Pages: 146

Brand: Magnescale Pages: 132

Brand: UNITED Pages: 22

Brand: Hafele Pages: 82

Brand: Samson Pages: 56

Brand: Hach Pages: 128

Brand: Yamato Pages: 33

GRAVIMETRIC AUGER FEEDER MGF-ST

Brand: Maguire Products Pages: 47

Brand: Magtrol Pages: 160

Brand: Nedap Pages: 20

Brand: Radware Pages: 98

Brand: RabbitCore Pages: 34

Brand: R82 Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands