Magnetek GPD 333 Technical Manual Download Page 41

Page: 41 / 81

To establish a V/f pattern with a straight line from Fmin to Fa,
set Fb = Fmin, and Vc = Vmin.

IMPORTANT

When entering a setting for one of these constants, an improper
constant fault will occur if any part of the following relationships
among constants

no-02

thru

no-08

is NOT TRUE:

a) Fmax

Fmin

b) Vmax > Vc

Vmin

The attempted setting value will blink for approx. 3 seconds,
then the display will again show the previous constant setting.

3.5

ACCEL / DECEL TIMES

These constants set the normal accel and decel times required
for the GPD 333 output to ramp from Fmin to Fmax or from
Fmax to Fmin, respectively.

If a Multi-function Input (terminal 3, 4 or 5) is programmed as
Accel/Decel Time Change command (see paragraph 3.15), the
GPD 333 uses the settings in

these

constants as its accel and

decel times when that input is closed.

Range (ea.) : 0.0 to 600.0 ( s )
Factory Setting (ea.) : 10.0

Constants

no-09
no-10

Accel Time 1
Decel Time 1

Accel Time 2
Decel Time 2

Constants

no-11
no-12

efesotomasyon.com - Yaskawa ac drive,servo motor

Summary of Contents for GPD 333


















































































Search results

Summary of Contents for GPD 333

Reviews:

Related manuals for GPD 333

Brands by name

Popular brands

Magnetek GPD 333, Technical Manual

Search results

Summary of Contents for GPD 333

Reviews:

Related manuals for GPD 333

Brands by name

Popular brands