Magnetek GPD 333 Technical Manual Download Page 27 | Manualshive

Page: 27 / 81

background image

14

1.5

START-UP.

1.5.1

Pre-power Checks.

• Wires properly connected and no erroneous grounds exist.

• Motor not connected to load. After start-up procedure is

completed, motor can be connected to load, and normal
operation can begin.

1.5.2

Status Display LEDs.

The standard GPD 333 has two

LEDs that can be monitored on the status plate. They are DS1
(GREEN) and DS2 (RED). The GPD 333 has been factory set
for external 2-Wire control and external speed reference (as
shown in Figure 1-5). The LEDs are the only status indicators
available without the optional Digital Operator. The chart
below explains GPD 333 status while monitoring the LEDs.

Drive

Status Plate

Status

DS1 DS2

Display Meaning

(GREEN) ( RED )

Normal

BLINKING

Off

Drive ready for operation, while in
stopped condition.

LIT

Off

Drive running.

Alarm

Off

BLINKING

Low input power, ext. base block in-

put, etc., while in stopped condition.

BLINKING BLINKING

External fault signal is present

at a drive input terminal (EF).

Protective

LIT

BLINKING

Overload protection (drive over-

Operation

load (OL), fin overheat (OH), etc.).

Off

BLINKING

Voltage protection (overvoltage

(OV), undervoltage (UV), etc.).

BLINKING

LIT

Overcurrent (OC), ground fault (GF).

LIT

LIT

Digital hardware memory fault

Drive

(CPF).

Fault

Off

Off

Hardware fault, such as control

power fault, CPU initialization, etc.

efesotomasyon.com - Yaskawa ac drive,servo motor

«
...
25
26
27
28
29
...
»

Summary of Contents for GPD 333


















































































Reviews:

No comments

Related manuals for GPD 333

Brand: Jafar Pages: 10

Brand: Jafar Pages: 8

Brand: Lakeshore Pages: 192

Brand: QUAD Pages: 16

Brand: Access Pages: 12

Brand: Harsco Industrial Pages: 57

Brand: Mamas & Papas Pages: 24

Brand: Mamas & Papas Pages: 24

Brand: Parkside Pages: 65

Brand: U-Prox Pages: 3

Brand: U-Prox Pages: 3

Brand: U-Prox Pages: 25

Brand: U-Prox Pages: 2

FSDrive-MV1000 Series

Brand: YASKAWA Pages: 260

Brand: YASKAWA Pages: 114

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 152

Brand: YASKAWA Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands