Loongson Godson 3A1000 User Manual Download Page 41

Page: 41 / 133

4/29/2020

Godson 3A1000 Processor User Manual

Set.

TDAL

35:32

0x0

0x0-0xf

When the auto-precharge parameter is set, this parameter defines

The number of auto-precharge and write recovery clock cycles.

TDAL = auto-pre write recovery

This parameter takes effect only after the AP is set.

PORT_CMD_ERROR

_TYPE

19:16

0x0

0x0-0xf

Type of command error on the port (read only)

Bit 0-Data bit width is too large

Bit 1 – Keyword priority address misalignment

Bit 2 – Keyword priority word count is not a power of 2

Bit 3-Error in narrow transform

CONF_CTL_10 [63: 0] Offset: 0xa0 DDR2 667: 0x0000003f3f140612

COMMAND_AGE_CO

UNT

37:32

0x0

0x0-0x3f

Define the command queue reordering logic when using the aging algorithm

The initial aging value of the command

AGE_COUNT

29:24

0x0

0x0-0x3f defines the command queue reordering logic when using the aging algorithm

Page 51

Godson 3A1000 Processor User Manual Part 1

The initial aging value of the command

TRC

20:16

0x0

0x0-0x1f

Define the active commands between the same bank of the memory module

The number of clock cycles, according to the specific memory particles and operating frequency

To configure.

TMRD

12: 8

0x0

0x0-0x1f

Define the clock cycle required to configure the memory module mode register

Number, usually 2 cycles

TFAW

4: 0

0x0

0x0-0x1f defines the tFAW parameter of the memory module, used when there are 8 logical banks

CONF_CTL_12 [63: 0] Offset: 0xc0 DDR2 667: 0x00002c0511000000

TRFC

47:40

0x0

0x0-0xff

Define the number of clock cycles required for the refresh operation of the memory module.

Configure according to specific memory particles and operating frequency.

TRCD_INT

39:32

0x0

0x0-0xff

Define the number of clock cycles between the memory module RAS and CAS,

Need to be configured according to specific memory particles and operating frequency.

TRAS_MIN

31:24

0x0

0x0-0xff

Define the minimum clock cycle of the effective command of the memory module row address

number

OUT_OF_RANGE_LE

NGTH

23:16

0x0

0x0-0xff Command length when out-of-bounds access occurs (read only)

ECC_U_SYND

15: 8

0x0

0x0-0xff Cause of 2bit uncorrectable error (read only)

ECC_C_SYND

7: 0

0x0

0x0-0xff Cause of 1-bit error correction error (read only)

CONF_CTL_17 [63: 0] Offset: 0x110 DDR2 667: 0x0000000000000c2d

TREF

13: 0

0x0

0x0-0x3ff

Define the clock interval between two refresh commands of the memory module.

Configure according to specific memory particles and operating frequency.

CONF_CTL_18 [63: 0] Offset: 0x120 DDR2 667: 0x001c000000000000

AXI0_EN_LT_WIDTH_

INSTR

63:48

0x0000

0x0-0xffff

Defines whether the AXI0 port receives memory accesses that are less than 64 bits wide

ask

CONF_CTL_19 [63: 0] Offset: 0x130 DDR2 667: 0x6d56000302000000

TRAS_MAX

63:48

0x0000

0x0-0xffff

Define the maximum number of clock cycles for the effective command of the memory module

It should be configured according to specific memory particles and operating frequency.

Summary of Contents for Godson 3A1000






































































































































Search results

Summary of Contents for Godson 3A1000

Reviews:

Related manuals for Godson 3A1000

Brands by name

Popular brands

Loongson Godson 3A1000, User Manual

Search results

Summary of Contents for Godson 3A1000

Reviews:

Related manuals for Godson 3A1000

Brands by name

Popular brands