Loongson Godson 3A1000 User Manual Download Page 77

Page: 77 / 133

4/29/2020

Godson 3A1000 Processor User Manual

Offset: 0x3C

Reset value: 0x00200000

Name: Bus Reset Control

Bit field

Bit field name

Bit width reset value Visit description

31:23 Reserved

0x0

Keep

twenty twoReset

0x0

R / W bus reset control:

0-> 1: Set HT_RSTn to 0, reset the bus
1-> 0: HT_RSTn is set to 1, the bus is reset

21:18 Reserved

0x0

Keep

B_interleave

0x0

Whether the R / W write response channel allows out-of-order execution (LS3A1000E and

Previous version)

When using multi-chip interconnect mode, it must be set to 1

Nop_interleave

0x0

Whether the R / W flow control channel allows out-of-order execution (LS3A1000E and above

version)

When using multi-chip interconnect mode, it must be set to 1

15: 0

Reserved

0x0

Keep

9.5.2

Capability Registers

Offset: 0x40

Reset value: 0x20010008

Name: Command, Capabilities Pointer, Capability ID

Bit field

Bit field name

Bit width reset value Visit description

31:29 HOST / Sec

0x1

Command format is HOST / Sec

28:27 Reserved

0x0

Keep

Act as Slave

0x0
/ 0x1

R / W HOST / SLAVE mode

The initial value is determined by the pin HOSTMODE
HOSTMODE pull-up: 0
HOSTMODE drop-down: 1

Reserved

0x0

Keep

twenty fourHost Hide

0x0

Whether R / W prohibits register access from HT bus

twenty threeReserved

0x0

Keep

22:18 Unit ID

0x0

In R / W HOST mode: can be used to record the number of IDs used

In SLAVE mode: record your own Unit ID

Double Ended

0x0

No dual HOST mode

Page 96

Godson 3A1000 Processor User Manual Part 1

Warm Reset

0x1

Bridge Control uses warm reset in reset

15: 8

Capabilities Pointer 8

0xa0

Next Cap register offset address

7: 0

Capability ID

0x08

HyperTransport capability ID

Offset: 0x44

Reset value: 0x00112000

Name: Link Config, Link Control

Bit field

Bit field name

Bit width reset value Visit description

Reserved

0x0

Keep

30:28 Link

Width Out

0x0

R / W Transmitter width

The value after cold reset is the maximum width of the current connection, write this post

The value of the register will be the next warm reset or HT
Effective after Disconnect

000: 8-bit mode
001: 16-bit mode

Reserved

0x0

Keep

26:24 Link Width In

0x0

R / W receiver width

The value after cold reset is the maximum width of the current connection, write this post

The value of the register will be the next warm reset or HT

Effective after Disconnect

twenty threeDw Fc out

0x0

The sender does not support double-word flow control

22:20 Max Link

Width out

0x1

The maximum width of the sending end of the HT bus: 16bits

Dw Fc In

0x0

The receiver does not support double-word flow control

18:16 Max Link

Width In

0x1

Maximum width of HT bus receiving end: 16bits

Summary of Contents for Godson 3A1000






































































































































Search results

Summary of Contents for Godson 3A1000

Reviews:

Related manuals for Godson 3A1000

Brands by name

Popular brands

Loongson Godson 3A1000, User Manual

Search results

Summary of Contents for Godson 3A1000

Reviews:

Related manuals for Godson 3A1000

Brands by name

Popular brands