LK ICS-RF8 Assembly Instructions Manual Download Page 30

Page: 30 / 31

LK Floor Heating | Assembly Instructions | LK Room Temperature Control ICS-RF8

EN.33.C.891008

Article overview

Article number

Name

Comments

2417302

LK Thermostat
ICS-RF High gloss
white

2417303

LK Thermostat
ICS-RF High gloss
black

2417304

LK Thermostat
ICS-RF Silver grey

2417307

LK Receiver Unit
ICS-RF8 (NO)

Intended for
normally open (NO)
actuators.

2417316

LK Receiver Unit
ICS-RF8 (NC)

Intended for
normally closed
(NC) actuators.

2417321

LK Repeater ICS

2417323

LK External Sensor
ICS

Length 3 m

2417324

LK Antenna Cable
ICS

Length 10 m

Technical data

Article name

LK Thermostat ICS

Article number

2417302, 2417303, 2417304

Setting range

8-40 °C

Supply voltage

3 x1,5 V

Battery life

2 years

Radio frequency

Self-modulation technique

Radio frequency

868 Mhz

Dimensions

100 x 100 x 20

Protection class

IP20

Operating temperature

+ 1 °C - + 50 °C

Storage temperature

- 20 °C - + 70 °C

Maximum humidity during
storage

No condensation

Article name

LK Receiver Unit ICS RF8

Article number

2417307 (NO), 2417316 (NC)

Supply voltage

230 V AC

Radio frequency

868Mhz

Regulating function

Self-modulation technique

Maximum number of actuators
per channel

3 pcs

Maximum number of actuators
per receiver unit

12 pcs

Dimensions

400 x 120 x 60

Protection class

IP30

Operating temperature

+ 1 °C - + 50 °C

Storage temperature

- 20 °C - + 70 °C

Maximum humidity during
storage

No condensation

Summary of Contents for ICS-RF8
































Search results

Summary of Contents for ICS-RF8

Reviews:

Related manuals for ICS-RF8

Brands by name

Popular brands

LK ICS-RF8, Assembly Instructions Manual

Search results

Summary of Contents for ICS-RF8

Reviews:

Related manuals for ICS-RF8

Brands by name

Popular brands